The Proteco Shark

  

Please refer to our terms and conditions of sale before finalising your purchase

 Click to Compare Swing Gate Actuators3 Year manufacturer's warrantyFree Next Day Delivery over £50You Can't Buy Cheaper!
 

The 230v Double Gate Kits consists of:

2 x Shark Operators and fittings
2 x Safety Photocells
1 x Electronic Control Unit
1 x Key Switch
2 x Remote controllers
1 x Override keys for use during power cuts
 

 

 
Product Voltage Max Gate Weight Gate Size Each Leaf Angle Type  Double Gate Single Gate
Shark Galvanised  230v 350Kg 3m to 110° * Underground motor £499.00  +vat  £465.00 +vat 
Shark Stainless Steel " 350Kg 3m to 110° * Underground motor £625.00  +vat £590.00 +vat
Shark 180º Adaptor Kit - - - to 180°  in-chamber mechanical adaptor £155.14 +vat £77.57 +vat
Opening Limit Stop
instead of gate stop set below		 - - - - in-chamber mechanical stop £34.27 +vat £17.14 +vat
Closing Limit Stop  instead of gate stop set below - - - - in-chamber mechanical stop £34.27 +vat £17.14 +vat

 Gate Stop set
instead of limit stops above

 - - - - above ground physical stop £35.00  +vat  £25.00  +vat 

                                            * up to 180° with optional adaptor
     
Postboxes   Intercoms   Accessories

The Proteco Shark underground kit is our premier product offering the most visually and aurally discreet gate automation system. This kit is one of our most popular and is recommended for new and existing swing gates, up to 3 metres each, hung on posts or pillars. May be fitted to gates that open outwards. Opening angles up to 180° (angles between 90° - 180° requires optional adaptor) may be achieved dependent on gate hinge position. The operators are non-reversible and therefore don’t need the inconvenience or expense of an additional electric lock to keep them closed.
If you don't want unsightly above ground stops, then you could purchase the optional Opening  Limit Stops & Closing Limit Stops which fit into the underground motor chambers to restricted the movement at the limits of travel.

 

Click to see manufacturer's data sheet,   Click to see fitting guide,   PDF reading problems? Click here

 

The motor mechanics are buried within secure steel (choose from galvanised or stainless) underground foundation boxes so as not to compete with the aesthetics of your gates; all that can be seen is the steel lid covering the operator box and a very small unobtrusive operator attached to the bottom edge of the gate leaf. As the motors are contained underground, environmental noise intrusion is minimal.

Designed for an intensive use by using a die-casting structure made of quality aluminium, stainless steel, bronze and steel. The fluid-grease lubrication system and the built-in thermal protection ensures a long-lasting working life in any weather conditions without the need for periodic maintenance.




Geometry
The Shark underground kit foundation box is installed beneath the gate at the foot of the hinge pillar. Refer to diagrams. The minimum distance between the vertical centre line of the hinges and the inner face of the pillar is 65mm. There must also be at least 65 mm between the lid of the foundation box and the bottom of the gate.

Remember if fitting underground drivers to wooden gates, it will be necessary to clad the gate bottom edge with metal to spread the load and to give something to attach the motor shoe. If you don't, the push-pull from the high torque will eventually split the wood.

Installation Hint:
When fitting Shark underground motors you will need a minimum of 65mm from your gate hinge point to the post.  Though soak-aways may be adequate, we recommend that you drain the motor case to lower lying land where possible. All underground motors will operate underwater when new, but if left submerged, it is likely that water will eventually enter the motor and / or cable insulation will become porous. It is better to correctly drain the foundation cases from day one to protect your investment! Some additional fabrication/welding may be necessary to connect the drive shoe to your gates.
 Only a single gate? Not sure if you need a right-hand kit or left-hand kit? Don't worry - the Shark kit is ambidextrous!
 

Options include: underground exit loop (detects the presence of a guest’s vehicle and automatically opens the gates for them); extra photocells; additional key fobs; intercom kit; long range (external) aerial; flashing beacon.

Tel: 01202 717191    Fax: 01202 717195